Current position > News detail
『Bounti Flower Near Me: Check Licensed Dispensary Menus Locally』Related information(v cone flow meter|rotary gas meter|gallon meter|gear meter|metal tube rotameter|glass tube rotameter|nutating disk meter|transit time ultrasonic flow meter|wedge flow meter|pd meters|hydraulic flow meter|ultrasonic water flow meter|water flow meter|air flow meter|magnetic water flow meter|oxygen flow meter|gas flow meter|argon flow meter|air velocity meter|gasoline flow meter|fuel flow meter|ultrasonic water meter|digital water meter|nitrogen flow meter|solid flow meter|Oxygen tank flow meter|digital water flow meter|diesel fuel flow meter|steam flow meter|02 flow meter|compressed air flow meter|oil flow meter|liquid flow meter)
```html
Bounti Flower Near Me: Check Licensed Dispensary Menus Locally
Quick Answer
Precision irrigation and nutrient dosing keep Bounti Flower products consistent batch to batch. Silver Automation Instruments supplies flow meters that measure water and liquid fertilizer down to 0.1% accuracy. Send us your pipe size (DN), flow range (L/h), and fertilizer type for a recommended model.
What Bounti Flower Growers Actually Need from a Flow Meter
A dispensary menu looks simple from the outside. Behind each strain on the list there is a grow room where water, nutrients, CO2, and temperature are controlled like a chemical plant. The flow meter sitting on the irrigation mainline is not a garden fitting. It has to read low flows during seedling phase and high flows during flush cycles without drifting. Most engineers skip this part. They pick a meter rated for 50 L/min and wonder why it reads zero at 0.5 L/min drip feed. We have seen this on customer sites many times.
In practice a Bounti Flower facility uses a combination of electromagnetic flow meters for irrigation loops and small oval gear meters for nutrient injection lines. The water source can be RO permeate. Conductivity can be below 5 µS/cm. That rules out most turbine meters because they need conductive liquid. Electromagnetic meters from Silver Instruments handle 0.05 µS/cm and above, so RO water is not a problem. Pulse output goes straight to the fertigation controller. No 4-20 mA converter box needed.
Fertilizer Dosing Lines Demand Oval Gear Meters
Concentrated nutrient stock tanks are small volume, low flow. A grower might dose 200 mL per minute of a calcium nitrate solution. With a 15 mm pipe and a flow rate of 12 L/h, the right tool is an oval gear flow meter. Our DN4 and DN6 models read 0.5 L/h to 60 L/h with ±0.5% accuracy. They are PT100-ready so you can do mass flow compensation for temperature. In one case a customer in Thailand growing medicinal flowers replaced a cheap paddle wheel sensor with an oval gear meter and saw fertigation accuracy jump from ±8% to ±1.2%. The recipe consistency improved enough that the harvest cycle shortened by 3 days.
Because the oval gear design measures actual displaced volume, it does not care about viscosity changes between different nutrient brands. Viscosity from 1 cP to 500 cP is linear on these meters. No need to recalibrate when switching from one nutrient line to another.
Drain Water Reuse and Ultrasonic Flow Meters
Large Bounti Flower greenhouses collect drain water, filter it, and mix it back into the fresh water supply. The return pipe is often DN50 to DN100, flowing maybe 20 m³/h. An ultrasonic clamp-on meter avoids cutting pipe and avoids pressure drop. Silver Instruments portable ultrasonic flow meter clamps on the outside of the pipe, reads flow rate, totalized volume, and sends data via Modbus RTU to the central controller. A 4-20 mA HART output also goes to the PLC. We have done this for a greenhouse project in Australia where the pipe was SS316L. Accuracy is ±1.0% of reading from 0.3 m/s to 10 m/s. The transducer holders stay mounted permanently for repeat measurement points.
So there is no need for a licensed plumber to install an in-line me
Pressure Transmitters for Spray Misting Systems
Propagation rooms for Bounti Flower clones use high-pressure misting (70 bar to 80 bar). A pressure drop of 5 bar means the nozzle pattern collapses. We supply pressure transmitters with flush diaphragm for this application. Our model reads 0 bar to 100 bar, outputs 4-20 mA, and comes with a Viton seal. The thread is G¼ male, so it screws directly into the pump manifold. No adapters. ATEX Zone 1 version is available if the misting room uses propane burners for CO2 generation. A customer in Spain replaced their gauge with this transmitter and caught a failing pump before it killed a batch of clones.
ATEX and Safety for Extraction Rooms
When a Bounti Flower facility also handles extraction, the room may be classified Zone 1 or Zone 2. Our Coriolis mass flow meter for ethanol or CO2 extraction flow is ATEX certified. It measures mass flow directly in kg/h, so you know exactly how much solvent is moving at any time. Because it measures density too, the controller can detect if the solvent-solute mix changes. For example, a sudden drop in density might mean the extraction vessel is dry. We have a DN15 Coriolis meter with 316L wetted parts, PTFE lining, and 4-20 mA HART output. It handles temperatures from -50 °C to 200 °C. Send us your solvent type, flow rate, and Ex zone classification for a quote.
Why Small Teams Choose Silver Instruments Over Big Brands
Bounti Flower operations are often run by a team of 5 to 20 people. The engineer who installs the meter also opens the packing box and reads the manual. Big brand meters arrive with a 200-page PDF and a price tag that includes premium for a logo. We make the same DN15 electromagnetic flow meter, same 316L electrodes, same 0.5% accuracy, for roughly 40% less. We also reply on WhatsApp within an hour during business hours. Late last year a grower in Canada sent us a photo of a broken flow meter at 11 PM their time. We shipped a replacement the next morning because we stock sensors in our Nanjing warehouse.
FAQ
Which flow meter for RO water with low conductivity?
Use an electromagnetic flow meter. Silver Instruments model reads down to 0.05 µS/cm.
Can I measure both flow and temperature with one sensor?
Yes. Our oval gear meters include a PT100 thermistor slot. You get pulse for flow and RTD for temperature.
Do you have a flow meter for CO2 gas flow in grow rooms?
Yes. Thermal mass flow meter for CO2, range 0.5 to 100 Nm³/h, 4-20 mA output. Specify gas type and pressure.
What is the lead time for a small order of 2 to 5 meters?
In stock models ship in 3 working days. Custom ATEX versions take 10 to 15 working days.
What information do you need for a quote?
Fluid type, pipe diameter (DN), flow range (min to max), pressure (bar), temperature (°C), output (4-20 mA, pulse, RS485), and Ex zone if applicable. Email [email protected] or WhatsApp +86-25-52155837.
Tel: +86-25-68650347
Email: [email protected]
WhatsApp: +86-25-52155837
WeChat: +86 15365082610
Web: flow-meter.com.au